Pressure washing OMZ

Lower pressure washing


Technology for cleaning undersides pressurized water OMZ is intended for washing the lower parts of trucks, buses, trolleybuses, trams and all other special road and rail vehicles.
 

The device consists of four basic components:

High Unit

Best cleaning results are obtained in the right proportion and quantity of water pressure. More than high pressure is important for exactly the amount of water that is supplied with high pressure unit. Dishwashing drawers standard bodywork road and rolling stock comes standard unit IPF 85/100. This unit adds one minute 85 liters of water under pressure of 100 bar.
Heating Unit

Default is used for water heating boiler with an oil burner. The hot water may be used as a gas burner or steam heat exchanger.
 
Washing Trolley

Washing trolley is made of stainless steel in combination with hot dip galvanized steel sheets. All parts are assembled with an effort to ease maintenance and servicing. Washing trolley moves across the surface covered by two tracks which are anchored to the sides of the washing channel. Are part of the structure, sliding rails and plastic energy chain with a guide chute. The propulsion system consists of two transmission speed of the engine located at the bottom of the truck, drive is direct. The truck wash are two rotary heads TW300. On each of the head are three high-pressure nozzles.
 
  Control and control panel

On this panel made the award of cleaning programs. Washing can be carried out both in the manual mode and automatic mode.

 

Rotary cleaning heads

Rotary cleaning heads are working through their own drive, which provides cold, or. pressure hot water. Operate on the principle of reaction water movement, which vystřikuje from nozzles and provides a rotary motion in an upright level and longitudinal axis. Movement speed rotary heads is dependent on the quantity and water pressure.

Body material is made of stainless steel, bronze and special plastic materials. The request can be made entirely from stainless steel design.

Rotary heads have wide application. Used eg for washing the inside of tanks and containers for cleaning of irregular shapes and surfaces, such as bodywork and chassis of vehicles, washing out the inside of the open bins and containers, small containers for washing, etc.
 

Pricelist rotary cleaning heads
 

Washing head W

Rotary head-washing equipment, operating through their own drive, made of stainless steel and bronze. The request can be made entirely from stainless steel design. Used to wash the inside of tanks and containers in general. Use water to 90 ° C, the weight of equipment 11 kg.
 
 

Washing Title V

These devices are similar to the device-head "W", diversity is only one rotor with two nozzles and counterweights on the opposite side. Use water to 90 ° C, the head weight is 11 kg.
 

Washing head WZ150

Washing equipment operating through their own drive are made of stainless steel and are suitable for washing the inside of containers with small entrance holes, which can not apply the head of "W" and "V". The minimum diameter of the inlet is 135 mm. Use water to 90 ° C, the head weight is 10 kg.
 
 

Washing heads TW

Washing heads working through their own drive are made of stainless steel and are suitable for washing of irregular shapes and surfaces, such as bodywork of vehicles, vehicle chassis, etc. The use of water to 90 ° C, the weight of equipment is 10 kg.
 

Washing heads LC

Washing equipment operating through their own drive are made of stainless steel and special plastic materials. When rotation is water spraying only the level of a hemisphere. Therefore, this device is used mainly for washing out the inside of containers and open containers. Use water to 90 ° C, the weight of the device is 8 kg.
   
 

Washing heads LC

Washing equipment operating through their own drive are made of stainless steel and special plastic materials. When rotation is water spraying only the level of a hemisphere. Therefore, this device is used mainly for washing out the inside of containers and open containers. Use water to 90 ° C, the weight of the device is 8 kg.
 
   
 

Washing head P 200

Washing facilities are made of stainless steel, driven by pneumatic motor and are suitable for minimum inlet port 2 ". Standard lengths in the range of 500-1000 mm is suitable for cleaning small tanks. This head can be powered from the normal high-pressure water cleaners.
 
   

Thermostatic regulator speed

Can be delivered to all wash heads working through their own drive. This component maintains a constant speed with varying water temperature fluctuations.
 

Transit cleaning wheels and chassis


Pressure washing of trucks and special vehicles